How to fill a staple gun with staples. How to insert staples into a furniture stapler? How to insert staples into a furniture stapler instructions

Don't know how to properly thread a large stationery or mini stapler? Read the article that describes this process in detail.

A stationery stapler is a stapler for paper and files. You can’t do without it either at home or in the office.

To use it, you need staples, without which the stapler will not work.
Staples are divided into sizes: No. 10, 26/8, 26/6, 24/8, 24/6. Their numbers are indicated on the packaging.
The packaging of the stapler itself indicates the numbers of the staples that fit it.
It seems that everything is simple - insert the staples of the required size into the stapler and you can start using it.
But many people have problems charging this device. How to do this correctly, read the following article.

So, you bought staples and want to charge your stapler. How to open and thread a large stapler with staples? Description in the form of instructions:

Fold back plastic cover stapler, which is supported by a spring. Opening the roof pulls a spring. The freed up space is the staple groove. Many large staplers have latches that need to be pulled back.
Take the staples- one section. Insert them into the groove, the ends should point down.
Close the stapler cover.
Click them once without paper. If a paper clip with bent ends falls out, it means the stapler is working.

Advice: If the staple that has fallen out is bent incorrectly or has not fallen out at all, then repeat the procedure or buy another stapler; there may be a malfunction.

You can watch the video to learn how to thread the stapler correctly. A visual demonstration will help you cope with this process quickly and without problems. In addition, the video explains how to repair a stapler.

Video: how to repair a stapler and charge the stapler?

Mini staplers are easier to refill than larger similar devices. Lift the plastic cover up and back. Now you can insert the staples into the groove. After completing the filling process, close the stapler and use it.

Advice: Mini staplers have a very small compartment for staples. Therefore, if you want to remove old staples or insert new ones, you will need tweezers.

Often the mini stapler may jam while filling. To fix this, open the lid and adjust the staples in the groove. If this is not done, the stapler may become unusable. Watch the video to see how to properly fill a mini-stapler.

Video: How to install staples in a stapler?

Video: stapler_stapler.AVI

A construction stapler is a multifunctional mechanism. It is used when it is necessary to connect identical or different not particularly hard materials to each other, for example, plastic, wood, film, insulation, plywood. This tool is called differently: tacker, staple gun, staple gun, nailer, staple gun. The individual elements are fastened to each other using staples, pins or small nails. To know how to properly work with a construction stapler, you need to understand its design, the types of fasteners suitable for it, and the method of setting up and replacing staples.

The furniture stapler is widely used by builders and furniture makers, as well as representatives of other fields of activity. By type of energy used To carry out a shot during operation, the following types of takers are distinguished:

mechanical;
electrical;
pneumatic.

The first two types are intended for domestic use, while the last type of tool is considered professional and is used mainly when performing large-scale work. The operating principle of mechanical and electric staple guns is based on pushing out fasteners by the force of a cocked (compressed) spring.

After pressing the trigger, it unclenches, which causes the striker to move. He strikes the staple (nail or pin), driving it into the surface of the material.

Mechanical stapler design

Manual (mechanical) staplers differ from their analogues in their simpler design. They consist of the following components and parts:
cocking handle;
a safety bracket that protects against accidental shots when transporting the tool;
impact springs;
shock absorber;
drummer;
striker;
impact force regulator, providing the ability to work with material of varying degrees of hardness (different densities);
housings;
charging spring;
store for fasteners;
rammer (with spring and lock);

tip that allows you to accurately drive fasteners.

The diagram of the staple gun device is shown in the photograph below. Impact mechanism

- this is the main unit of the stapler, cocked by the force of the worker’s muscles. It can be equipped with two types of springs:
spring (plate).

Manufacturers indicate in the operating instructions for products the type of spring installed.

Coiled spring mechanism, shown in the photo above, are equipped with cheap models. They can be easily distinguished by the adjusting screw located on the tool body on the opposite side of the staple outlet hole. But it is also possible that the wing will be missing, then you will need to refer to the instructions to determine the type of spring installed.

Leaf springs more powerful, but more expensive than twisted analogues. At the same time, the impact of a tool equipped with them during operation is less. They also have a long service life and are easier to cock. The leaf spring mechanism is installed on models intended for professional use.

To make it easier to work with the tool, the handle is covered with rubber pads, and the magazine is made with a transparent insert (which makes it easy to control the presence of staples or nails).

Design features of electric and pneumatic staplers

The device of a network-type electric stapler is shown in the photo below.

The numbers in the photograph correspond to the following structural elements:

trigger;
fuse;
handle with special coating;
power cord;
on/off switch;
shock force regulator;
pusher mechanism;
shop.

Located inside the instrument electric drive and impact mechanisms. In this case, the electric motor is designed to charge the spring.

Battery models do not have a power cord: batteries are installed instead.

Furniture stapler device pneumatic type more complex than mechanical analogues. Pneumatic tools consist of the following structural elements:

impact force regulator, providing the ability to work with material of varying degrees of hardness (different densities);
a cylinder with a piston located inside it;
starting systems (trigger mechanism);
magazine for fasteners with a pusher;
impact mechanism;
inlet fitting designed to connect a hose to the tool high pressure;
regulator of penetration depth of fasteners (impact force);
air distribution unit.

A pneumatic type squeegee operates from the energy of compressed air supplied by a compressor or from a cylinder. After pressing the trigger, the gas passes through the air distribution unit. Further compressed air

enters the cylinder, causing the piston to move. The latter transfers energy to the striker striking the fastener. After impact, the staple or nail is driven into the surface of the material.

To use a staple gun, you need staples. They are divided into separate types according to the following criteria:

according to the material from which they are made;
by degree of hardness;
by the presence of coverage;
by size;
according to form.

According to the material of manufacture

Staples according to material are:

aluminum, used when working with non-solid materials;
copper (expensive), also intended for soft parts;
steel, suitable for both non-solid and soft materials, but rust over time;
made of stainless steel (stainless steel) - this is a reliable option in the most different conditions, but with a high price.

Furniture staples can also be galvanized to prevent them from rusting.

By hardness

Based on hardness, fasteners are divided into the following types:

simple;
very hard;
red-hot.

The ends of the fasteners can also be sharpened differently, making it easier to drive in under certain conditions.

By shape

Based on the shape of the staples, the following types are distinguished:

U-shaped;
U-shaped;
T-shaped (pins).

Most often in practice, fasteners in the form of the letter U are used, and U-shaped ones are used mainly when laying cable lines. The pins are almost invisible fasteners. They are used when fasteners must be as invisible as possible.

Standard staple sizes

Almost all tacker manufacturers also produce their own brackets for them. But at the same time, there is a mandatory standardization of product sizes - this allows you to insert staples into a staple gun from different companies when replacing them.

The dimensions of fasteners mean the following parameters:

staple thickness (indicated English letter A);
the length (width) of its back (b);
leg height (depth).

Based on these dimensional parameters, the following are distinguished: the most popular types of staples in practice.

53 is the most common standard size with a=0.7 mm, b=11.4 mm and a leg height of 4÷14 mm.
140, having the following dimensions: back width equal to 10.6 mm, thickness 1.2 mm and depth from 4 to 14 mm.
36 - This marking indicates that U-shaped fasteners can be used for the staple gun.
300 are nails that are only suitable for a staple gun.

It should be taken into account that different companies designate the same types of fasteners differently. To match fasteners from different manufacturers, use the table below. Determining the size of the staples will not be difficult at all.

There are no universal types of fasteners suitable for any type of work.

How to insert staples into a stapler

Changing staples in a mechanical tack is easy. To charge a new fastener, proceed as follows:

the tool is blocked from accidental activation using a fuse;
on the back side of the staple gun, open the magazine cover, behind which there is a groove for fasteners;
a rod equipped with a pusher spring is taken out from the inside;
the strip of staples is turned with its points against the handle, and then inserted into the groove;
install the rod with the spring inside the tool in its original place, where they clamp the fasteners;
close the magazine lid;
remove the fuse;
make several shots in test mode to check the functionality of the tool.

With nails When charging the stapler, proceed in the same way.

The photo below shows how to place staples in a mechanical stapler.

Blocking the staple gun from accidental firing is a mandatory procedure to ensure the safety of the work.

To thread pneumatic staples or electric staplers, operate according to a scheme similar to a mechanical tool:

block the device;
turn the instrument over;
by pressing a special button, take out the tray for the fasteners;
correctly insert staples or pins (nails) into the tray;
insert the “clip” until a click appears;
unlock the tool and check its operation.

When you press the stapler button, the fastener tray may slide out or its cover will open - this depends on the stapler model used.

Some modifications of mechanical staple guns have a different principle for replacing fasteners: they are made with a chute that extends when you press a button. Staples are placed in the elongated tray and inserted back into the magazine until it clicks. The entire process, showing in detail how to thread the staples in the case considered, is demonstrated in the video:

The sequence of adjusting the stapler

Setting up a staple gun is needed in the following cases:

after purchasing the tool before starting work;
if the stapler stops completely driving in the fasteners;
when starting to work with a material of a different density than the previous one.

If the stapler stops driving in fasteners completely, this is due to gradual hammer spring wear or with its loosening. For some time, the adjustment will help, but after that you will need to purchase a new stapler.

You should take into account the dimensions of the fasteners for which the tacker is designed: if the size of the staples exceeds what is allowed according to the operating instructions, then adjustment has nothing to do with it, you just need to select the appropriate consumables.

Mechanical staple guns with a coil spring have a screw that regulates the degree of compression. It is shown in the photo below with a red arrow.

If you tighten the adjusting screw clockwise, the spring will compress more strongly and its potential energy will increase. The result will be a blow greater strength. The ejected staple will go deeper into the surface of the material. Turning the adjuster counterclockwise will loosen the spring. The blow will also become weaker. By rotating the screw, you can adjust the stapler to work with material of varying hardness (density).

For mechanical models of staple guns with a spring (leaf) spring of the impact mechanism, the regulator is located under the handle. By rotating it in different directions, the force of the shot is adjusted. It is necessary to reconfigure the impact mechanism every time you start working with a different material. After adjusting the spring compression, it is recommended to test the tool's performance on a workpiece that is no longer needed.

The adjustment process ends when the fasteners enter the entire length of the legs into the material without piercing it with the “back.” It is recommended to practice by rotating the adjuster from minimum to maximum spring compression.

Rules for safe use of the tool

When working with a construction stapler, it is imperative to follow safety regulations. The main requirements boil down to the following points.

When replacing staples you need block the tool using a fuse against sudden, unexpected activation.
It is prohibited to point the tool at your hand or other part of your own body, as well as at other people or animals.
When transporting or storing the stapler, it is necessary to secure its handle with a safety lock.
Only a person in a normal psychological state (not under the influence of alcohol, psychotropic substances or drugs) is allowed to work with a staple gun.
The workplace should be well lit and kept clean.
It is necessary to constantly use such individual protection means like glasses so that nothing accidentally flies into the eye. To prevent the bracket from flying off when fired, you need to monitor the presence of metal inclusions on work surface, promptly bypassing or removing them.
If the fastener gets stuck, it must be carefully removed.
When working with workpieces small sizes They must be fixed motionless using a vice or clamps; it is prohibited to hold them with your hands.
Your body position should always be stable and as comfortable as possible, and your shoes should have non-slip soles.

Instructions for safe work with electric and pneumatic staplers contains additional points:

corded power tools must not be used inside hazardous areas;
Only switched off equipment is allowed to be connected to the outlet;
the power cord with plug and the body of the model being used must be intact;
It is prohibited to use an electric staple gun in the rain or indoors with high levels of humidity;
unauthorized persons must be kept at a distance of more than 2 m;
the pneumatic tool used, the high-pressure hose attached to it, as well as other parts of the system must be free of mechanical damage;
During work, it is necessary to ensure that the power cord is located behind the tool so that it does not interfere.

Nothing complicated when using mechanical, pneumatic, and also electrical types There are no construction staplers. It is only necessary to use suitable fasteners (specified in the operating instructions) for the job, and before doing so, adjust the impact mechanism to suit the specific material. At the same time, constant adherence to safety precautions will prevent injury. Attentiveness and accuracy are one of the main keys high-quality execution any work.

A stapler (translated from English as “stitcher”) is a necessary thing in everyday life and at work. A stationery stapler is designed for fastening sheets and files. There are five types of staplers: manual, manual office, desktop horizontal or vertical, stitching, printing. They all differ, first of all, in the number of sheets that can be stitched at a time.

You will need

– stapler;
– staples.

Instructions

1. Determine what type of stapler you have. To do this, see how many sheets you can sew at a time. The most primitive in design are pocket staplers. They are prepared for stapling up to 10 sheets. Manual office ones have a special recess on the fingers and allow you to fasten up to 30 sheets. Tabletop horizontal or vertical ones have a rubber or plastic sole; they sew up to 50 sheets. In stitching machines, it is allowed to staple up to 150 sheets, and in printing machines, which have maximum depth firmware, connect up to 250 sheets at a time. The specificity of stapling with a stapler is through fastening, which you carry out using a metal staple. The staple pierces the sheets being stapled right through, and its ends rest against the plate located at the end of the other side of the stapler.

2. Before loading the stapler, determine the size of staples that is suitable for it. Staples (also called paper clips) come in several types: No. 10, 26/8, 26/6, 24/8, 24/6. These numbers are written on the packaging. Staples must be packaged in carton boxes 500, 1000 or 2000 pieces each. You will find out which of the above are suitable for your stapler by looking at its packaging.

3. In order to load the stapler with the selected staples, bend its cover. It is connected by a spring to a plastic element, the one that presses the staples to the opposite edge of the metal groove, the one that holds the staples. Opening the cover will pull the spring and, consequently, the plastic element, thus freeing up space for new staples.

4. Take one section of staples and place them in the metal groove, ends facing down. Close the lid and click the stapler once to test. If a staple with concave ends inward falls out of it, it means you did everything correctly, but if this did not happen, or the staple was bent abnormally, then repeat the procedure or change the stapler.

A stapler is a universal thing. It will always come in handy not only in a professional environment, but also in a home environment. Nail insulation, cover the greenhouse with film, change the upholstery of furniture or secure a cable - the possibilities for application are wide. There are so many pistols on the market today, it's not always easy to know which one is best. But it is important to understand this issue, because different types pistols are used in different ways. The device, the type of tool, the size of the staples - your head can spin.

Pistols can be divided into several groups:

mechanical;
electrical;
pneumatic.

Use of mechanical staplers

Usually in everyday life they use simple mechanical device. In another way it is called a construction stapler. If you need a tool for one-time use (upholstering a greenhouse), then it will be quite enough. It can be made of plastic or metal. Plastic is cheap, but breaks quickly. Metal is more reliable and a little more expensive. Which one is more suitable, you need to decide for yourself.

What if the choice fell on mechanical construction stapler? How to use? Very simple.

Tips for using a mechanical stapler:

Operation of electrical appliances

Most often, electric staplers for furniture are used for reupholstering interior items and other large-scale repair work. They differ from mechanical ones by having more massive charges. Their service life is longer. And it’s easier to use electric ones. This furniture stapler costs several times more than mechanical models.

People often ask a question about a furniture stapler. How to choose? There are many options here. Electric staplers differ in the following parameters:

How to insert staples into furniture stapler powered by electricity? The scheme is simple. Just find the button on the back of the gun and pull out the sliding bar. Then load the staples with the ends down and push the gutter. It is important to follow safety precautions.

Pneumatic construction staplers

Differences from mechanical and electrical devices:

Staplers are useless without staples. And the “cartridges” differ in many ways. Manufacturers themselves make all kinds of projectiles for staplers.

Material:

Hardness level:

Simple - suitable for working with malleable materials.
Solid - used to interact with dense materials such as plastic and wood.
Hardened - for the most stubborn surfaces.

An important point will be sharpening the ends of the staples. Spicy? They will get clogged much easier.

Flat ones are the most popular types of staples; there is a very large selection of them.
Semicircular - more often used to secure cables.
Pins (look like the letter "T") are used to hide the fasteners. The most inconspicuous ones.

Each stapler has its own type of staples. The marking is indicated on the pistol box or on the body. It is important to use only staples that match the markings, otherwise the device will work by shooting several fasteners or not work at all.

What to do if the gun does not release staples:

Safe work techniques

Using a mechanical stapler.

By following safety precautions when using the device, you will avoid unnecessary injury. And the device will last longer:

When working with an electric or pneumatic stapler, you must follow the safety rules described for mechanical tools. More important:

Mechanical, electric or pneumatic staplers are easy to use. But it is important to use the tool correctly. You need to charge it with fasteners with the markings indicated for your model. It is also necessary to adjust the mechanism for the required force of driving in staples. The main thing: follow safety rules when using. Careful handling and careful use are the key productive work with any stapler.

A stapler (translated from English as “stapler”) is a necessary thing in the office. A stationery stapler is designed for quickly fastening sheets of paper using metal staples.

Types of staplers

Staplers are divided into several types: according to the number of sheets that can be stitched simultaneously.

Mini stapler

Compact model that can be put in your pocket. Staples from 10 to 20 sheets. Staples for mini-staplers come in different sizes: 10, 24/6. The design and color of the case are very interesting: colored, transparent, there are devices that look more like a toy than a stapler itself.

Desk stapler

The stapler is quite compact, does not slip on the table and does not leave scratches on it, as it has a rubber sole. Stitches from 10 to 50 sheets. Standard staples are used: 10, 24/6-8.

Booklet stapler

A specialized stapler with adjustable stitching depth. Equipped with a ruler for ease of use. Sews brochures, catalogs and newspapers along the fold of the pages. Designed for different numbers of sheets, works on different staples.

Printing or typographic stapler

The most powerful stapler. Stitches archives, voluminous stacks of paper. Used in government agencies, libraries, clinics. On average it stitches up to 250 sheets. Designed for both standard staples and specialized ones.

Antistapler (destapler)

Designed to remove staples from paper. The anti-stapler is often built into the stapler itself; it extends from the back of the stapler and uses a pointed tip to pry up and remove the staple. But what looks much more original on the table is a small object resembling a frog, which firmly grips the bracket on both sides. Anti-staplers come in the form of ordinary paper knives with a curved tip.

Stapler-plier
A plier is a special stapler in the form of pliers; it can be used outdoors. Plyer is used by florists when packing bouquets; it is suitable for attaching labels or labels to fabric.

Tucker

This is an “installation stapler”, made in the form of tongs. Hammers staples like nails. Used for pinning announcements and posters. Interestingly, many desktop staplers found today perform the function of a tacker.

Staplers also vary in the type of staples that are used with them.

Stapler No. 10

Designed for fastening a small number of sheets, usually up to 15 sheets of standard weight paper.

Stapler No. 23

The most powerful stapler.

Works with 23 types of staples. Depending on the length of the leg of the staple used, it fastens up to 260 sheets of paper.

Staplers No. 24

A universal stapler that staples both small quantities (1-2 sheets) and large quantities (20-30 sheets).

What to look for when choosing a stapler

. Staples

There are always two numbers written on the staples, for example, 24/6 - what does this mean?

The first number is the staple type. This is a conventional unit, which includes the staple width, cross-sectional dimensions and wire steel grade (caliber) defined for this standard.

The second number is the height of the leg. It is measured in millimeters. The greater the height of the leg, the large quantity sheets can be stapled. The thickness of the bracket increases in proportion to its height. To determine the maximum thickness of the sheets to be sewn, subtract 3-4 mm from the length of the legs for their bend.

When choosing the length of the staple leg, remember the main rule - 2/3 of the leg should be in the material being fastened, and 1/3 will hold the material being attached.

A high-quality staple is made from cut wire (equal in diameter on any segment) - then all staples will be equal. A quality staple has pointed ends that allow it to pierce paper easily.

What material should I choose for the bracket? To fasten thick paper and large stacks, we recommend using steel wire staples, as they are stronger than galvanized iron. By the way, all staples with a leg height of 10 mm or more are made of steel.

The quality of the staples is related to the reliability of the stapler, so if you buy a quality stapler, then it is worth purchasing the corresponding staples.

. Internal organization stapler

The internal mechanism of the stapler is very great importance and will affect the operation of the device.

The stapler motor system is driven either by a spring or a special metal plate. What's better? The plate is more practical: it lasts longer and provides softer sliding, and the spring has a habit of stretching. The stapler tongue is made of metal (more durable) or plastic (provides smooth feeding of staples).

. Case and design

Pay attention to the material from which the stapler is made - its durability depends on it. Metal body more reliable in operation and look very impressive. But plastic also has advantages: it is lighter, more convenient for transportation, and more pleasant to hold in your hands. Models with combined cases are very convenient: metal + plastic, metal + rubber, metal + plastic + rubber.

The color of the stapler depends on the size and specific application.

The more powerful the stapler, and the more features it performs, the more subdued its color.

. Power and depth

The characteristics of a stapler always indicate the punching power (or volume of fastening) - how many sheets or millimeters of paper the stapler punches. As a rule, office printing paper with a density of 80 g/m2 is taken into account.

Punching depth is the distance from the edge of the paper to the punching point. The depth of firmware in mini-staplers is 35-40 mm, in desktop staplers - from 50 mm or more.

. Package

The packaging will always tell about the quality of office supplies, be it a stapler or staples for it. In addition, the product itself must have markings indicating the country of origin, company and type of bracket used. Sometimes a package of staples is included with the stapler.

. Paper

The thickness of a standard sheet of office paper is 80g/sq.m. It is worth considering that depending on the thickness of the sheets being stapled, the power of the stapler will also vary.

How to charge a stapler

Before you load your stapler, determine the size of staples that will fit it.

The number of the staple used in a particular stapler is written on the packaging.

Bend the cover of the stapler. It is connected by a spring to a plastic element that presses the staples against the opposite edge of the metal groove in which the staples are placed. Opening the cover will pull the spring, followed by a plastic element, thus freeing up space for new staples.

Take one section of staples and place them in the metal groove, ends facing down. Close the lid and click the stapler once to test. If a staple with concave ends falls out of it, it means everything is working, but if this does not happen, or the staple is bent incorrectly, repeat the procedure or change the stapler.

← go back

Mechanical stapler allows you to nail plastic panels, clamps for lining, fabric for furniture, wooden or plastic surfaces.

There are three types of staplers: mechanical, electric and pneumatic.

Mechanical staplers are affordable, compact, lightweight, and easy to maneuver. Below we will only talk about them.

How to choose a stapler?

In short, it is not advisable to buy the cheapest options, and also plastic models. Metal tool more powerful and reliable.

Choose professional models that have an adjusting screw (thumb) at the top. It helps regulate the force with which the tool will pierce the material.

Many people forget

Before work, adjust the adjusting screw according to the material of the surface you are going to work with.

If it is hard plywood, strong penetration of the material will be required, therefore, it is worth setting a high force. If it is a loose surface, the force must be reduced so as not to break through the fabric, or for example pvc panel which you are targeting.

During operation, it is recommended to press the lever with one hand and press the adjusting screw with the thumb of the other hand. Then the recoil will be minimal and the load will be distributed evenly in the stapler. You will be able to nail the brackets much better.

How to insert staples into the receiver

The design of all mechanical hammers is almost the same. There is a handle-lever, due to which pressing occurs, and at the bottom of the stapler there is a metal plate that opens the receiver. This is where we have to load the staples.

Before you buy brackets at a hardware store, you need to find out what size will fit your device. As a rule, the size and type of suitable staples are indicated on its body.

For example, the body of our stapler indicates a width of 12 mm and a depth of 6-14 mm. This means that you will only be able to charge staples in this range.

Parentheses less than or bigger size will not fit the receiver. The size of the staples in millimeters is also indicated on their packaging.

To insert projectiles into the stapler, you need to open the metal plate on the back surface.

To do this you need to take it big and index finger on both sides, then pull it towards you and slightly downwards. Thus, we press the metal tab on the back surface of the plate, and pull out a metal spring, similar to the one found in a regular office stapler.

If there are any staples left in your stapler, they will fall out once the spring is pulled out. If they are not there, then it’s time to install new ones for further work.

The staples are inserted into the receiver (the hole is in the “P” position).

How many shells will fit?

Now a little about how many shells fit into a stapler. Staples are sold in small rows. The row can be divided into several parts yourself by slightly breaking it with your hands.

The tool is filled with 1-1.5 rows. 2 rows rarely fit in the bin, so if there is a lot of work to be done, it is better to prepare half rows before starting work.

What to do if a bracket gets stuck

It is worth noting one more very important point, which will help you in your work.

How to fill a staple gun with staples

It happens that the staples become bent and get stuck in the exit hole. They cannot be hammered into the surface and cannot be pulled out by hand.

In this case, we will need to pull out the feed magazine completely.

This option exists for almost all professional staplers.

First you have to re-open metal plate and remove the spring.

This will remove the entire feed magazine that was in the tool.

You will see a jammed staple that can now be easily pulled out by hand.

Putting the stapler back together is not difficult: the entire pulled out block returns to its place with a press.

You should hear a click when you do this. Afterwards, do not forget to replace the spring.

Not just parentheses

Some staplers can work not only with staples, but also with studs various forms. The designations of what the stapler works with are indicated on its body or in the instructions.

I tuck the nails into the stapler in the same way as with staples, but you need to be careful after pulling out the spring. A row of nails must be loaded along one of the outer edges of the letter “P”, and not inside this very letter!

If you want it to produce two nails side by side when working with a stapler, load the second row along the second outer edge. Next, the spring is inserted and the stapler is closed.

Stapler, how to charge a construction stapler?

Very often in construction there is a need to connect parts. This is done using nails or staples. At the modern level, a tool such as a stapler is used. There are many types of this tool, but in all of them the principle is the same - fastening with staples. The stapler can be charged by itself when they run out.

How to refill a stapler

They, just like the stapler, are sold at any hardware store or construction markets. There are features that you can see in this video.

To insert a new block of staples into the construction stapler, you must remove the clamping bar, which is located in the rear part of the stapler.
Next, insert the staples with their paws down and insert the clamping bar again. In order for the stapler to work without interruption and not to hit two or three staples at once (you must admit that this happens to many people), you need to use only those staples that are recommended by the stapler manufacturer.